Lots of people have fireplaces in their homes, but keeping them clean and smoke free takes some maintenance and effort on the part of the homeowner. The fireplace will not maintain itself, even though there are some fireplace cleaning logs on the market these days. These will not completely replace a professional cleaning, though, so you should have one of these done at least every year or two.
You should also have the proper tools stored next to your fireplace and these are available in many different materials and types. Cast iron is a good and durable material, but fireplace tools are also available in brass, pewter, nickel, and etcetera. There is a large selection on the market and you will surely be able to find what you are looking for.
A fireplace blower can help build up the fire and add more heat to it. You have probably seen one of these before and it can be a real help when first starting to build a fire.
Fireplace tongs can be used to move around logs that are obviously too hot to pick up with your hands and this is necessary, since the logs will not always be exactly where you need them to be to get the most heat and longevity out of the fire.
A fireplace poker can be used to stir around coals and spread them so that the heat is more evenly distributed. This helps larger logs catch on fire faster than they normally would.
A shovel is used to clean out the ashes that are left after a fire is out and a small broom is necessary to keep the area immediately outside the fireplace cleaned up.
If you are having problems building a fire that does not spill smoke back into the room, you need to make sure that nothing is blocking the chimney on top of the house. Leaves, bird nests, and sticks can clog it up during the spring, summer, and fall and make it completely unusable.
Using the correct wood is also important; logs that are freshly cut and have a lot of moisture still in them will smoke instead of catch fire. Use logs that are dried out and try to store them in a place where they will not get wet.
Start the fire slowly by building it up with paper and small sticks at first to get the chimney warm. Warming up the chimney is important so that the air inside it becomes warm instead of cold. Cold air pushes the warm air and smoke down and back into the house.
Jim Corkern is a writer and promoter of quality
Miami Residential Water Damage Restoration Contractors and
Orlando water Damage companies.
Thursday, October 18, 2007
Techniques Used to Clean Up Mold
While there are a lot of different ways to kill and remove mold from your home, depending on what the mold has gotten on or into, you may want to use one technique before trying the other. Note that killing mold and removing it is not one and the same thing. Killing mold is just that: terminating the life of the mold so that it ceases to continue growing. Since the mold is dead, it cannot cause infections if it gets onto your skin because it must be alive to change into yeast. However, the bad thing about simply killing the mold is the fact that it does not have to be alive in order to cause an allergic reaction in a person. The mold spores remain intact and in their same physical condition as before, so when the spores enter the body, the body does not realize that the spores are dead and pose no threat.
You can use a wet vacuum to clean up standing water in areas of your home where it exists, since this is where mold likes to grow the most. This is especially true if there are any cellulose-based materials that have been soaked by it, such as paper, cardboard, and anything else that can be decomposed. You should only use these vacuums when the surface is wet, so mold spores do not get tossed into the air. The equipment should be cleaned and dried thoroughly after you use it, since mold and its spores can attach themselves to it.
Sometimes you can use a damp paper towel or damp cloth to clean mold off of surfaces that are nonporous, like countertops or a vinyl floor, but if you are going to do this, using chemicals that kill mold are a must. Trying to clean mold off of porous surfaces like drywall usually ends in heartbreak, because most of the time they cannot be saved. The entire item is usually too contaminated. Clothes can be saved sometimes, but this is only because of the very thin nature of the item. Thick porous surfaces like drywall are simply too thick for it to be feasible to try to save them.
HEPA filter-equipped vacuum cleaners are good to have around if you are trying to remove as much mold from your home as possible, since these vacuum cleaners will filter clean air back into the room as you vacuum. The mold spores and dirt particles will get caught in the filter and are easily disposed of afterward. When you dump the contents of the receptacle, do not touch it with your bare hands. Wear gloves if you can and do not let it come into contact with your skin. Try not to stir the contents up and do not breathe them.
Jim Corkern is a writer and promoter of quality
Houston Fire Damage Water Restoration Contractor companies and
Los Angeles Water Damage and Restoration Services.
You can use a wet vacuum to clean up standing water in areas of your home where it exists, since this is where mold likes to grow the most. This is especially true if there are any cellulose-based materials that have been soaked by it, such as paper, cardboard, and anything else that can be decomposed. You should only use these vacuums when the surface is wet, so mold spores do not get tossed into the air. The equipment should be cleaned and dried thoroughly after you use it, since mold and its spores can attach themselves to it.
Sometimes you can use a damp paper towel or damp cloth to clean mold off of surfaces that are nonporous, like countertops or a vinyl floor, but if you are going to do this, using chemicals that kill mold are a must. Trying to clean mold off of porous surfaces like drywall usually ends in heartbreak, because most of the time they cannot be saved. The entire item is usually too contaminated. Clothes can be saved sometimes, but this is only because of the very thin nature of the item. Thick porous surfaces like drywall are simply too thick for it to be feasible to try to save them.
HEPA filter-equipped vacuum cleaners are good to have around if you are trying to remove as much mold from your home as possible, since these vacuum cleaners will filter clean air back into the room as you vacuum. The mold spores and dirt particles will get caught in the filter and are easily disposed of afterward. When you dump the contents of the receptacle, do not touch it with your bare hands. Wear gloves if you can and do not let it come into contact with your skin. Try not to stir the contents up and do not breathe them.
Jim Corkern is a writer and promoter of quality
Houston Fire Damage Water Restoration Contractor companies and
Los Angeles Water Damage and Restoration Services.
Mold And Water In Your Two Most Important Rooms
A good meal and a good bath is something that most Americans enjoy thoroughly, but how can you enjoy either one when you’re in a room full of ugly water damage stains on the walls, floors, and ceilings? Many of these rooms often have the brown stains on the ceiling that are typical of water damage and while most people just paint over them, often the stains just keep coming back because the underlying problem has not been fixed yet.
It is probably due to a leaky roof, but what about the steam that comes off of your bath water or off of the stove when you cook dinner? These every day tasks can be just as much of a cause of water damage as a leaking roof can be, if not more so because they happen every day. At least, a bath a day comes recommended, anyway. Installing a steam vent in your bathroom for under $100 and a day’s work could possibly be one of the best investments that you can make to help safeguard the appearance and structural integrity of your kitchen and bathroom.
Make sure that you do not allow your bath tub or your kitchen sink to overflow. Sometimes we turn on the bath water and get stuck talking to a relative or a co-worker on the phone, all the while unaware that the water you wanted in your tub is pouring all over your floor. The same thing can happen when you are cooking in the kitchen or washing dishes. This can land quite a lot of water in your floor before you realize it and can do quite a bit of damage to your floor if you let it happen often.
An overflowing toilet is also a hazard, not only because of the water damage that can occur, but also due to the possible sewage content of the water when you go to flush it. If not cleaned up properly, mold can start to grow around the base of the toilet, especially if you have carpet in your bathroom. Carpet in the bathroom is a no-no.
Also avoid throwing wet dirty clothes into your bathroom floor or closet, especially if you happen to have a carpeted bathroom. You will probably forget that these wet clothes are there and throw dry ones on top of it.
This results in water damage and mold growth more often than not when the closet is not cleaned out. The best thing to do is to wash wet clothes and towels as soon as possible so they are not forgotten about or at the very least stored separately from dry dirty clothes.
Jim Corkern is a writer and promoter of quality
water damage restoration companies and
Dallas Residential Water Damage Restoration Contractors.
It is probably due to a leaky roof, but what about the steam that comes off of your bath water or off of the stove when you cook dinner? These every day tasks can be just as much of a cause of water damage as a leaking roof can be, if not more so because they happen every day. At least, a bath a day comes recommended, anyway. Installing a steam vent in your bathroom for under $100 and a day’s work could possibly be one of the best investments that you can make to help safeguard the appearance and structural integrity of your kitchen and bathroom.
Make sure that you do not allow your bath tub or your kitchen sink to overflow. Sometimes we turn on the bath water and get stuck talking to a relative or a co-worker on the phone, all the while unaware that the water you wanted in your tub is pouring all over your floor. The same thing can happen when you are cooking in the kitchen or washing dishes. This can land quite a lot of water in your floor before you realize it and can do quite a bit of damage to your floor if you let it happen often.
An overflowing toilet is also a hazard, not only because of the water damage that can occur, but also due to the possible sewage content of the water when you go to flush it. If not cleaned up properly, mold can start to grow around the base of the toilet, especially if you have carpet in your bathroom. Carpet in the bathroom is a no-no.
Also avoid throwing wet dirty clothes into your bathroom floor or closet, especially if you happen to have a carpeted bathroom. You will probably forget that these wet clothes are there and throw dry ones on top of it.
This results in water damage and mold growth more often than not when the closet is not cleaned out. The best thing to do is to wash wet clothes and towels as soon as possible so they are not forgotten about or at the very least stored separately from dry dirty clothes.
Jim Corkern is a writer and promoter of quality
water damage restoration companies and
Dallas Residential Water Damage Restoration Contractors.
Mold in My Rice, Please
A favorite food in Asia for the past thousand years is called red yeast rice and it considered a traditional part of the dish most of us are familiar with, at least by name, called Peking duck. The system of Traditional Chinese Medicine has put the dish to use by claiming that it assists the body in keeping a healthy circulatory system and promotes a healthy heart. Its use has been documented back as long ago as the Tang imperial dynasty in China in the approximate year of 800 A.D. There could possibly be a fair reason for the claim that it helps keep a good circulatory system, since current research has proven that it is pretty good at lowering your cholesterol. But, what is this “red yeast rice”, exactly?
Well, red yeast rice is produced by fermenting a mold called “monascus purpureus” that has been put on top of rice. The natural ingredient mevinolin is supposedly what gives the dish its cholesterol lowering characteristic, since this ingredient is similar to that which doctors typically give a person to help lower high cholesterol, such as the drugs Zocor and Lipitor. Even though we all need a certain amount of cholesterol in order to survive and be healthy, most of the time our own bodies produce enough of it to maintain survival. We only actually need to obtain about twenty percent of our cholesterol from the food that we take in every day. Red yeast rice (or mevinolin, whichever you want to say) blocks the enzyme in the liver that causes it to produce cholesterol.
Even though this medicine food has been used in China for at least a millennia in the treatment of high cholesterol and maintaining a healthy circulatory system, it has only begun to see some use in the United States and other western countries. Mevinolin is actually sold as a dietary supplement in some places and is available over the counter without a prescription.
If you do happen to eat red yeast rice, it is not a good idea to eat it or take the mevinolin supplements if your doctor has already put you on Zocor or Lipitor.
Monascus purpureus is a red-purplish mold that is used primarily in Asian foods to provide color and was used for this long before food dyes were invented. In addition to providing a healthy amount of color to a dish, it can also give the food a good flavor, too.
Jim Corkern is a writer and promoter of
Emergency Water Damage Restoration and
Houston Water Damage Restoration Which are Certified IICRC Water damage and mold remediation contractors.
Well, red yeast rice is produced by fermenting a mold called “monascus purpureus” that has been put on top of rice. The natural ingredient mevinolin is supposedly what gives the dish its cholesterol lowering characteristic, since this ingredient is similar to that which doctors typically give a person to help lower high cholesterol, such as the drugs Zocor and Lipitor. Even though we all need a certain amount of cholesterol in order to survive and be healthy, most of the time our own bodies produce enough of it to maintain survival. We only actually need to obtain about twenty percent of our cholesterol from the food that we take in every day. Red yeast rice (or mevinolin, whichever you want to say) blocks the enzyme in the liver that causes it to produce cholesterol.
Even though this medicine food has been used in China for at least a millennia in the treatment of high cholesterol and maintaining a healthy circulatory system, it has only begun to see some use in the United States and other western countries. Mevinolin is actually sold as a dietary supplement in some places and is available over the counter without a prescription.
If you do happen to eat red yeast rice, it is not a good idea to eat it or take the mevinolin supplements if your doctor has already put you on Zocor or Lipitor.
Monascus purpureus is a red-purplish mold that is used primarily in Asian foods to provide color and was used for this long before food dyes were invented. In addition to providing a healthy amount of color to a dish, it can also give the food a good flavor, too.
Jim Corkern is a writer and promoter of
Emergency Water Damage Restoration and
Houston Water Damage Restoration Which are Certified IICRC Water damage and mold remediation contractors.
Salvaging a Watery Electronic Device
Whether you own a cell phone, CD player, laptop, or any other small electronic device, you probably know that letting such a device come into contact with a liquid surely means the sudden death of it. This is somewhat of a misunderstanding, simply because of the fact that it is not the water alone that makes water and electrical devices coming into contact with each other a dangerous thing for your item.
What makes water a bad thing to let get onto or into your electronic devices is whether or not electricity is running through it at the time of contact. It is the electricity that does the real damage and not the liquid itself. If you were to put a CD player or a cell phone that had no electrical current running through it into a puddle of normal water (not containing any dirt particles or sand or chemicals), then there would probably be next to no damage done to it, since most circuit boards are made of plastic and do not absorb water very well. Unfortunately, putting something like that into chemically treated or dirty water could cause more problems than just the water contact.
If you do happen to drop your cell phone or CD player into a bath tub or sink full of water, get it out of the water in less than 20 seconds in order to minimize the damage. Getting it out in under 20 seconds is important because it takes about that long for the water to get inside the item and to the item’s circuit board, especially if it as airtight as most cell phones are these days. Cell phones are not completely water tight, which is the reason for the time limit. Even if the phone is on, it can be saved if you get it out in time. Remove the battery as quickly as possible and lay it on the side with openings for the water to drain out, such as on the keypad if it was a cell phone.
Put the device into a bowl of uncooked rice at least overnight and this should absorb the majority of the water from both the inside and outside of it. Do not replace the battery or try to power on the device until you are certain that it is completely dry inside. Trying to turn it on could be exactly what does the damage that you are trying to avoid.
Jim Corkern is a writer and promoter of
Texas Water Damage Restoration and
Houston Water Damage Restoration Which are Certified IICRC Water damage and mold remediation contractors.
What makes water a bad thing to let get onto or into your electronic devices is whether or not electricity is running through it at the time of contact. It is the electricity that does the real damage and not the liquid itself. If you were to put a CD player or a cell phone that had no electrical current running through it into a puddle of normal water (not containing any dirt particles or sand or chemicals), then there would probably be next to no damage done to it, since most circuit boards are made of plastic and do not absorb water very well. Unfortunately, putting something like that into chemically treated or dirty water could cause more problems than just the water contact.
If you do happen to drop your cell phone or CD player into a bath tub or sink full of water, get it out of the water in less than 20 seconds in order to minimize the damage. Getting it out in under 20 seconds is important because it takes about that long for the water to get inside the item and to the item’s circuit board, especially if it as airtight as most cell phones are these days. Cell phones are not completely water tight, which is the reason for the time limit. Even if the phone is on, it can be saved if you get it out in time. Remove the battery as quickly as possible and lay it on the side with openings for the water to drain out, such as on the keypad if it was a cell phone.
Put the device into a bowl of uncooked rice at least overnight and this should absorb the majority of the water from both the inside and outside of it. Do not replace the battery or try to power on the device until you are certain that it is completely dry inside. Trying to turn it on could be exactly what does the damage that you are trying to avoid.
Jim Corkern is a writer and promoter of
Texas Water Damage Restoration and
Houston Water Damage Restoration Which are Certified IICRC Water damage and mold remediation contractors.
Subscribe to:
Posts (Atom)
